smartctl 6.6 2017-11-05 r4594 [x86_64-w64-mingw32-w10-1709] (sf-6.6-1) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST1000LM024 HN-M101MBB Serial Number: S31LJ9HG505011 LU WWN Device Id: 5 0004cf 20fb40240 Firmware Version: 2BA30001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Nov 15 18:48:24 2018 RTZST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: (12540) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 209) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1288 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 092 088 025 - 2526 4 Start_Stop_Count -O--CK 097 097 000 - 3788 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 6511 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 333 12 Power_Cycle_Count -O--CK 097 097 000 - 3802 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 2408264 183 Runtime_Bad_Block -O--CK 100 100 010 - 108 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 1218 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 070 054 040 - 30 (Min/Max 10/46) 191 G-Sense_Error_Rate -O---K 100 100 000 - 686 192 Power-Off_Retract_Count -O---K 100 100 000 - 196 193 Load_Cycle_Count -O--CK 084 084 000 - 165220 194 Temperature_Celsius -O---- 064 054 000 - 30 (Min/Max 10/46) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 34 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 2 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 12018 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 1223 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1223 [6] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 4d 16 b3 78 40 00 00:00:00.110 READ FPDMA QUEUED 60 00 00 00 80 00 00 4d 16 b3 78 40 00 00:00:00.133 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:00:00.133 READ LOG EXT 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.108 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.131 READ FPDMA QUEUED Error 1222 [5] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 a8 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.108 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.131 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:00:00.131 READ LOG EXT 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.108 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.129 READ FPDMA QUEUED Error 1221 [4] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 a8 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.108 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b3 78 40 00 00:00:00.129 READ FPDMA QUEUED 60 00 00 00 90 00 00 4d 16 b2 e8 40 00 00:00:00.129 READ FPDMA QUEUED 60 00 00 00 70 00 00 00 36 84 40 40 00 00:00:00.129 READ FPDMA QUEUED 60 00 00 00 90 00 00 4d 16 b3 e8 40 00 00:00:00.128 READ FPDMA QUEUED Error 1220 [3] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b2 e8 40 00 00:00:00.108 READ FPDMA QUEUED 60 00 00 00 90 00 00 4d 16 b3 e8 40 00 00:00:00.126 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b2 e8 40 00 00:00:00.126 READ FPDMA QUEUED 60 00 00 00 70 00 00 00 36 84 40 40 00 00:00:00.126 READ FPDMA QUEUED 61 00 00 00 08 00 00 72 0d ef 70 40 00 00:00:00.126 WRITE FPDMA QUEUED Error 1219 [2] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b2 e8 40 00 00:00:00.105 READ FPDMA QUEUED 61 00 00 00 08 00 00 72 0d ef 70 40 00 00:00:00.123 WRITE FPDMA QUEUED 60 00 00 00 90 00 00 4d 16 b5 e8 40 00 00:00:00.123 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b4 e8 40 00 00:00:00.123 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b3 e8 40 00 00:00:00.123 READ FPDMA QUEUED Error 1218 [1] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b2 e8 40 00 00:00:00.105 READ FPDMA QUEUED 61 00 00 00 08 00 00 72 0d ef 78 40 00 00:00:00.121 WRITE FPDMA QUEUED 60 00 00 00 90 00 00 4d 16 b9 e8 40 00 00:00:00.121 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b8 e8 40 00 00:00:00.121 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b7 e8 40 00 00:00:00.121 READ FPDMA QUEUED Error 1217 [0] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b2 e8 40 00 00:00:00.103 READ FPDMA QUEUED 60 00 00 00 a8 00 00 4d 16 b9 e8 40 00 00:00:00.118 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b8 e8 40 00 00:00:00.118 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b7 e8 40 00 00:00:00.118 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b6 e8 40 00 00:00:00.118 READ FPDMA QUEUED Error 1216 [7] occurred at disk power-on lifetime: 6508 hours (271 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 4d 16 b3 d0 40 00 Error: UNC at LBA = 0x4d16b3d0 = 1293333456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 4d 16 b2 e8 40 00 00:00:00.100 READ FPDMA QUEUED 60 00 00 00 a8 00 00 4d 16 b9 e8 40 00 00:00:00.116 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b8 e8 40 00 00:00:00.116 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b7 e8 40 00 00:00:00.116 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 16 b6 e8 40 00 00:00:00.116 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 90% 6503 - # 2 Short offline Completed: read failure 90% 6503 1265822392 # 3 Short offline Completed: read failure 90% 6503 1265822392 # 4 Short offline Completed: read failure 90% 6503 1265822392 # 5 Short offline Completed: read failure 90% 6503 1265822392 # 6 Short offline Completed: read failure 90% 6502 1265822392 # 7 Short offline Completed: read failure 90% 6500 1265822392 # 8 Short offline Completed without error 00% 6108 - # 9 Short offline Completed without error 00% 3243 - #10 Short offline Completed without error 00% 2825 - #11 Short offline Completed without error 00% 2129 - #12 Short offline Completed without error 00% 1641 - #13 Short offline Completed without error 00% 1504 - #14 Short offline Completed without error 00% 1289 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Aborted_by_host [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 27/30 Celsius Lifetime Min/Max Temperature: 12/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (84) Index Estimated Time Temperature Celsius 85 2018-11-15 08:10 30 *********** 86 2018-11-15 08:15 36 ***************** 87 2018-11-15 08:20 35 **************** 88 2018-11-15 08:25 37 ****************** ... ..( 2 skipped). .. ****************** 91 2018-11-15 08:40 37 ****************** 92 2018-11-15 08:45 36 ***************** 93 2018-11-15 08:50 37 ****************** 94 2018-11-15 08:55 37 ****************** 95 2018-11-15 09:00 35 **************** 96 2018-11-15 09:05 36 ***************** 97 2018-11-15 09:10 37 ****************** 98 2018-11-15 09:15 37 ****************** 99 2018-11-15 09:20 36 ***************** 100 2018-11-15 09:25 35 **************** 101 2018-11-15 09:30 37 ****************** 102 2018-11-15 09:35 37 ****************** 103 2018-11-15 09:40 37 ****************** 104 2018-11-15 09:45 38 ******************* 105 2018-11-15 09:50 37 ****************** 106 2018-11-15 09:55 36 ***************** 107 2018-11-15 10:00 37 ****************** 108 2018-11-15 10:05 37 ****************** 109 2018-11-15 10:10 37 ****************** 110 2018-11-15 10:15 38 ******************* 111 2018-11-15 10:20 36 ***************** 112 2018-11-15 10:25 37 ****************** 113 2018-11-15 10:30 28 ********* 114 2018-11-15 10:35 32 ************* 115 2018-11-15 10:40 34 *************** 116 2018-11-15 10:45 35 **************** 117 2018-11-15 10:50 36 ***************** 118 2018-11-15 10:55 34 *************** 119 2018-11-15 11:00 34 *************** 120 2018-11-15 11:05 34 *************** 121 2018-11-15 11:10 36 ***************** 122 2018-11-15 11:15 33 ************** 123 2018-11-15 11:20 23 **** 124 2018-11-15 11:25 25 ****** 125 2018-11-15 11:30 25 ****** 126 2018-11-15 11:35 25 ****** 127 2018-11-15 11:40 26 ******* 0 2018-11-15 11:45 30 *********** 1 2018-11-15 11:50 32 ************* 2 2018-11-15 11:55 34 *************** 3 2018-11-15 12:00 35 **************** 4 2018-11-15 12:05 35 **************** 5 2018-11-15 12:10 29 ********** 6 2018-11-15 12:15 33 ************** 7 2018-11-15 12:20 35 **************** 8 2018-11-15 12:25 35 **************** 9 2018-11-15 12:30 35 **************** 10 2018-11-15 12:35 31 ************ 11 2018-11-15 12:40 32 ************* 12 2018-11-15 12:45 32 ************* 13 2018-11-15 12:50 32 ************* 14 2018-11-15 12:55 33 ************** 15 2018-11-15 13:00 31 ************ 16 2018-11-15 13:05 32 ************* 17 2018-11-15 13:10 35 **************** 18 2018-11-15 13:15 36 ***************** 19 2018-11-15 13:20 37 ****************** 20 2018-11-15 13:25 37 ****************** 21 2018-11-15 13:30 35 **************** 22 2018-11-15 13:35 37 ****************** 23 2018-11-15 13:40 35 **************** 24 2018-11-15 13:45 35 **************** 25 2018-11-15 13:50 34 *************** 26 2018-11-15 13:55 33 ************** 27 2018-11-15 14:00 33 ************** 28 2018-11-15 14:05 35 **************** 29 2018-11-15 14:10 34 *************** ... ..( 2 skipped). .. *************** 32 2018-11-15 14:25 34 *************** 33 2018-11-15 14:30 33 ************** 34 2018-11-15 14:35 33 ************** 35 2018-11-15 14:40 34 *************** 36 2018-11-15 14:45 34 *************** 37 2018-11-15 14:50 34 *************** 38 2018-11-15 14:55 35 **************** 39 2018-11-15 15:00 33 ************** 40 2018-11-15 15:05 32 ************* 41 2018-11-15 15:10 32 ************* 42 2018-11-15 15:15 34 *************** 43 2018-11-15 15:20 36 ***************** 44 2018-11-15 15:25 34 *************** 45 2018-11-15 15:30 33 ************** 46 2018-11-15 15:35 35 **************** 47 2018-11-15 15:40 34 *************** 48 2018-11-15 15:45 37 ****************** 49 2018-11-15 15:50 35 **************** 50 2018-11-15 15:55 32 ************* 51 2018-11-15 16:00 33 ************** 52 2018-11-15 16:05 34 *************** 53 2018-11-15 16:10 36 ***************** 54 2018-11-15 16:15 35 **************** 55 2018-11-15 16:20 34 *************** 56 2018-11-15 16:25 34 *************** 57 2018-11-15 16:30 35 **************** 58 2018-11-15 16:35 35 **************** 59 2018-11-15 16:40 37 ****************** 60 2018-11-15 16:45 36 ***************** 61 2018-11-15 16:50 35 **************** 62 2018-11-15 16:55 36 ***************** 63 2018-11-15 17:00 36 ***************** 64 2018-11-15 17:05 31 ************ 65 2018-11-15 17:10 32 ************* 66 2018-11-15 17:15 34 *************** 67 2018-11-15 17:20 33 ************** 68 2018-11-15 17:25 36 ***************** 69 2018-11-15 17:30 33 ************** 70 2018-11-15 17:35 32 ************* 71 2018-11-15 17:40 33 ************** 72 2018-11-15 17:45 31 ************ 73 2018-11-15 17:50 31 ************ 74 2018-11-15 17:55 30 *********** 75 2018-11-15 18:00 30 *********** 76 2018-11-15 18:05 29 ********** 77 2018-11-15 18:10 30 *********** 78 2018-11-15 18:15 29 ********** 79 2018-11-15 18:20 27 ******** 80 2018-11-15 18:25 30 *********** 81 2018-11-15 18:30 30 *********** 82 2018-11-15 18:35 32 ************* 83 2018-11-15 18:40 31 ************ 84 2018-11-15 18:45 29 ********** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific